**Distributed generation, which is an emerging technological trend around the world, poses a new set of challenges for the energy industry. With the real possibility of bi-directional power flow and the erosion of the conventional generation, transmission, distribution, retail sequence, the inevitable outcome is that distribution networks need to handle network protection in both forward and reverse power flow scenarios.**

While directional protection is not a new concept, it provides a significant degree of additional complexity in comparison to traditional magnitude-based protection schemes. This technical article covers the underlying physics to help engineers and technicians understand the concepts behind directional protection and for what applications it is most suited.

Distribution networks with a high penetration of solar renewable energy connections often run backwards during the day (power flow towards the substation) and forwards at night (power flow away from the substation). This phenomenon is becoming increasingly common and requires directional protection implemented on all protection devices installed on these feeders to provide correct fault detection and protection co-ordination.

**Directional overcurrent**

Overcurrent is typically applied for faults which don’t include an earth leakage. This class of faults include lines clashing together (a phase to phase fault), a branch falling across the lines, or some short circuit connection between phases. It is not the best protection to detect earth faults.

Directional overcurrent is the calculation of the difference between the phase angle of the current and the phase angle of the voltage. To oversimplify, if the voltage and current vectors point the same way, it’s probably forward, and if they point in opposite directions, the fault is probably reverse.

The typical industry practice for relays is to convert the phase measured currents and voltages to sequence components (positive, negative and zero sequence voltages and currents). Overcurrent direction is calculated on the difference between the angle of the positive sequence voltage (V_{ps}) and the positive sequence current (I_{ps}).

Let’s explore a fault scenario to get this understanding. Consider the following situation:

We have a source on either side of this network, and depending on the configuration, the fault could either be forward or reverse from the perspective of the midline recloser (an automatic circuit breaker with integrated current transformers, voltage sensors and microcontroller relay).

Firstly, let us take the most simple case, when we assume the cable is a resistor. The qualitative vectors for the V_{ps} and I_{ps} are shown in Fig. 2.

From Fig. 2, we will consider fault A as a forward fault. The fault angle then between V_{1} and I_{1} would be approximately 0°. For the converse case, a reverse fault, the difference would be approximately 180°.

Commonly, the fault angle range is up to 90° either side of the “most forward/reverse case”.

If the Relay Characteristic Angle (RCA) indicated the fault was forward from -90, through 0 to 90°, the fault would be picked up as forward, and reverse for anything else.

But why do we care about such a large range of angles for a forward fault?

The reality is that an electricity distribution network is not purely resistive, and the angle shift relationship between voltage and current depends on both the reactive and resistive components of the network – the *X* and *R* values.

Conceptually, when we look at the fault vector diagram, the resistive values are along the *x* axis, and the reactive values are along the *y* axis. The more reactance (which could be capacitive or inductive), the more the vectors move away from the resistive line.

The reason that engineers set an operating range, is to catch all the cases for a forward fault, whilst rejecting all the reverse cases (or vice versa). Depending on your cable choices and network, the amount of *X* and *R* depending on the fault distance from the circuit breaker will result in very different angle readings.

Characteristic |
95mm^{2} Al |
240mm^{2} Al |

Resistance | 0,31 Ω/km | 0,12 Ω/km |

Reactance | 0,15 Ω/km | 0,3 Ω/km |

X/R Ratio |
0,48 | 2,5 |

The table above outlines a few values for an example comparison between two aluminium conductors. One is a 95 mm^{2} cross section, and the other a 240 mm^{2}. The interesting value here is the *X/R* ratio. The *X/R* ratio shows that for a given length of line, you can expect a certain amount of reactance and resistance.

When the ratio is below 1, the longer the cable, the more resistive it is. That is, the further the fault is away from your circuit breaker, the closer the voltage-current vector difference will be to zero.

When the ratio is above 1, the longer the cable, the more reactive it is. The further the fault is away from your circuit breaker, the further the voltage – current vector difference will be apart.

In other words, depending on your cable, the vector difference will either diverge or converge because of the ratio between *X* and *R*. Fig. 4 shows qualitative current vectors based on the *X* and *R *relationship.

The reason that directional overcurrent has a “relay characteristic angle” or “torque angle” (a legacy term), is to account for the reactance of your network. You can assume that if the forward angle drifts based on reactance, then a similar drift will happen in the opposite direction. Therefore, a directional overcurrent setting of say 60° assumes a fairly reactive network, with resultant operating ranges being from 150°, down through 60° and down to -30°. The reverse cases would be the opposite.

In summary:

- Directional overcurrent is determined through multiple techniques, but the most common is through a comparison between V
_{ps}angle and I_{ps }angles. - If the network was purely resistive, a fair assumption would be that forward has a vector difference of zero, and reverse faults have a vector difference of 180°.
- The biggest reason for phase shift between voltage and current is the
*X/R*ratio at a fault site. - All practical networks have some reactance, and the reason for a relay characteristic angle is to account for all the overcurrent fault cases, as the ratio between
*X*and*R*varies along the length of the protected feeder. - The more resistive a network is, the closer the RCA is to 0°. The more reactive it is, the closer the RCA is to 90°.

Contact John Dykes, Noja Power, johnd@nojapower.co.uk

950

10